Dt 466e Trouble Code List [Archive] - TheDieselGarage.com

: Dt 466e Trouble Code List


hacksaw
11-12-2006, 05:00 PM
Looking For Dtc Trouble Code List For 98 Ih 4900 Dt 466e

TheBac
11-12-2006, 09:10 PM
Moved to Medium Duty section....

2003EDGE
11-13-2006, 02:19 AM
FLASH CODE
CIRCUIT INDEX
FAULT DESCRIPTION

111
ECM
No Fault Detected - Flash code only

112
ECM PWR
Electrical System Voltage B+ out of range HIGH

113
ECM PWR
Electrical System Voltage B+ out of range LOW

114*
ECT
Engine Coolant Temperature signal out of range LOW

115*
ECT
Engine Coolant Temperature signal out of range HIGH

121*
MAP
Manifold Absolute Pressure Frequency Out of Range

122*
MAP
Manifold Absolute Pressure Signal is inactive

123
MAP
Manifold Absolute Pressure (MAP) above spec. level at low idle

124*
ICP
Injection Control Pressure Signal out of range LOW

125
ICP
Injection Control Pressure Signal out of range HIGH

131*
APS/IVS
Accelerator Position Signal out of range LOW

132*
APS/IVS
Accelerator Position Signal out of range HIGH

133*
APS/IVS
Accelerator Position Signal in-range fault

134*
APS/IVS
Accelerator Position and Idle Validation disagree

135*
APS/IVS
Idle Validation Switch circuit fault

141
VSS
Vehicle Speed Signal out of range LOW

142
VSS
Vehicle Speed Signal out of range HIGH

143
CMP
Wrong number of CMP signal transistions per cam revolution

144
CMP
CMP signal noise detected

145
CMP
CMP signal inactive while ICP has increased

151
BARO
Barometric Pressure Signal out of range HIGH

152
BARO
Barometric Pressure Signal out of range LOW

154
IAT
Intake Air Temperature Signal out of range LOW

155
IAT
Intake Air Temperature Signal out of range HIGH

211*
EOP
Engine Oil Pressure Signal out of range LOW

212*
EOP
Engine Oil Pressure Signal out of range HIGH

213
SCCS
Remote Throttle Signal out of range LOW

214
SCCS
Remote Throttle Signal out of range HIGH

221
SCCS
SCCS Switch or Circuit fault

222
BRAKE
Brake Switch Circuit fault

223
DCL/ATA
VPM not communicating with ECM

224
KAM PWR
KAM Corrupt

231
DCL/ATA
ATA common fault

232
DCL/ATA
Unable to forward ECM message to ATA DCL

233
TACH
Tachometer Buffer is inactive

234
DCL/ATA
Unable to forward ATA message to ECM

235
DCL/ATA
VPM/ECM DCL fault

241
IPR
Injection Pressure Regulator OCC Self Test failed

242
ECM/IDM
FDCS signal to IDM OCC Self Test failed

243
IDM PWR
IDM Power Relay OCC Self Test failed

244
EDL
Engine to Transmission Data Line (EDL) OCC fault

253
ECM/IDM
Fuel Injection Sync Circuit OCC Self Test failed

254
ECM
OCC Self Test ECM test circuit out of range HIGH

255
ECM
OCC Self Test ECM test circuit out of range LOW

311*
EOT
Engine Oil Temperature Signal out of range LOW

312*
EOT
Engine Oil Temperature Signal out of range HIGH

313
EOP**
Engine Oil Pressure below warning level

314
EOP**
Engine Oil Pressure below critical level

315*
-
Engine Speed (Tach RPM) limit exceeded

321
ECT**
Engine Coolant Temperature above warning level

322
ECT**
Engine Coolant Temperature above critical level

323
ECL
Engine Coolant Level below warning / critical level

325
ECT
Power reduced, matched to cooling system performance

331*
IPR
Injection Control Pressure above system working range

332*
ICP
Injection Control Pressure above spec with engine off

333*
IPR
Injection Control Pressure above / below desired level

421
INJ
LOW to HIGH Side Open - Cyl 1

422
INJ
LOW to HIGH Side Open - Cyl 2

423
INJ
LOW to HIGH Side Open - Cyl 3

424
INJ
LOW to HIGH Side Open - Cyl 4

425
INJ
LOW to HIGH Side Open - Cyl 5

426
INJ
LOW to HIGH Side Open - Cyl 6

431
INJ
LOW to HIGH Side Short - Cyl 1

432
INJ
LOW to HIGH Side Short - Cyl 2

433
INJ
LOW to HIGH Side Short - Cyl 3

434
INJ
LOW to HIGH Side Short - Cyl 4

435
INJ
LOW to HIGH Side Short - Cyl 5

436
INJ
LOW to HIGH Side Short - Cyl 6

441
INJ
LOW Side Short to VBAT- Cyl 1

442
INJ
LOW Side Short to VBAT- Cyl 2

443
INJ
LOW Side Short to VBAT- Cyl 3

444
INJ
LOW Side Short to VBAT- Cyl 4

445
INJ
LOW Side Short to VBAT- Cyl 5

446
INJ
LOW Side Short to VBAT- Cyl 6

451
INJ
Low Side Short to ground - Cyl 1

452
INJ
Low Side Short to ground - Cyl 2

453
INJ
Low Side Short to ground - Cyl 3

454
INJ
Low Side Short to ground - Cyl 4

455
INJ
Low Side Short to ground - Cyl 5

456
INJ
Low Side Short to ground - Cyl 6

461
Perf Diag.
Cyl. Contribution Test Failure - Cyl 1

462
Perf Diag.
Cyl. Contribution Test Failure - Cyl 2

463
Perf Diag.
Cyl. Contribution Test Failure - Cyl 3

464
Perf Diag.
Cyl. Contribution Test Failure - Cyl 4

465
Perf Diag.
Cyl. Contribution Test Failure - Cyl 5

466
Perf Diag.
Cyl. Contribution Test Failure - Cyl 6

511*
INJ
Multiple Faults Bank 1

512*
INJ
Multiple Faults Bank 2

513*
INJ
High Side to Bank 1 Open

514*
INJ
High Side to Bank 2 Open

515*
INJ
Bank 1 High Side Short to ground or VBAT

521*
INJ
Bank 2 High Side Short to ground or VBAT

522*
IDM PWR
IDM Fault

523*
IDM PWR
IDM power voltage is low

524*
INJ
Both High Side Switches shorted together

531*
ECM / IDM
Fuel Injection Sync Signal Low: Cylinder Identification Signal (CI)

532*
ECM / IDM
Fuel Injection Sync Signal High: Cylinder Identification Signal (CI)

541*
ECM / IDM
IDM Feedback TOGGLE not detected by ECM

543*
ECM / IDM
IDM faults not received

544*
INJ
Injector Fault in Bank 2

545*
INJ
Injector Fault in Bank 1

612*
CMP
Incorrect ECM installed for CMP (timing) wheel

613*
VPM
Installed ECM not compatible with VPM software

614*
VPM
Installed ECM not compatible with ECM software

615
ECM
Programmable parameter KAM Corrupt fault

621*
VPM
Engine using MFG. Default rating Program Engine

622*
VPM
Engine using Field Default rating

623*
VPM
Invalid Engine rating Code: Check VPM programming

625
ECM
Module software Background Process was inactive

631
ECM
ROM (Read Only Memory) Self Test Fault

632
ECM
RAM Memory - CPU Self Test Fault

633
DCL / ATA
VPM is communicating incorrectly with ECM

634
VPM
Internal Fuelmeter memory location in error

635
VPM
Internal Hourmeter memory location in error

641
VPM
Internal Odometer memory location in error

642
VPM
Internal Fuelmeter fault

643
VPM
Internal Hourmeter fault

644
VPM
Internal Odometer fault

645
VPM
Internal EEPROM memory location error

651
VPM
Feature memory data content corrupted

652
VPM
Engine/Fuel memory data content corrupted

653
VPM
Engine/Rating memory data content corrupted

654
VPM
Watchdog Timeout



*- Indicates WARN ENGINE LAMP on when fault is set.

* *- Faults only available if Engine Protection is enabled

2003EDGE
11-13-2006, 02:19 AM
That is good for 1995-1999 DT466E engines. Good Day!

hacksaw
11-13-2006, 12:13 PM
Thanks

2003EDGE
11-13-2006, 06:27 PM
No problem :)

TheBac
11-14-2006, 01:45 AM
I'll sticky this for you guys....

2003EDGE
11-14-2006, 08:21 AM
I can also post the newer engine DTC lists if you would like.

bobthebuilder
12-27-2006, 02:37 PM
yes plz, and thank you:Thumbup:

ACE Tow
01-16-2007, 03:11 AM
To: 2003Edge
If you could post the trouble codes for the later DT466E i would appreciate it.
I have ordered the Intl. CD Manual but would like to start on the codes in my 2002 truck. It runs but has some unknown codes in it. Thanks

SKOLJACK
02-05-2008, 10:26 PM
To: 2003Edge
If you could post the trouble codes for the later DT466E i would appreciate it.
I have ordered the Intl. CD Manual but would like to start on the codes in my 2002 truck. It runs but has some unknown codes in it. Thanks

You can go to this site: https://evalue.internationaldelivers.com/service/bodybuilder/general/engine/eges270_FC.xml and click on the actual code (DTC) to access some decent diagnosis pages!

Or scroll down for a quick reference.

111 - No errors detected - flash code only

112 - ECM PWR Electrical system voltage B+ out-of-range high

113 - ECM PWR Electrical system voltage B+ out-of-range low

114 - ECT Engine Coolant Temperature signal out-of-range low

115 - ECT Engine Coolant Temperature signal out-of-range high

121 - MAP Intake Manifold Absolute Pressure signal out-of-range high

122 - MAP Intake Manifold Absolute Pressure signal out-of-range low

123 - MAP Intake Manifold Absolute Pressure signal in-range fault

124 - ICP Injection Control Pressure signal out-of-range low

125 - ICP Injection Control Pressure signal out-of-range high

126 - Engine Brake Control Pressure signal out-of-range low

127 - BCP Engine Brake Control Pressure signal out-of-range high

131 - APS/IVS APS signal out-of-range low

132 - APS/IVS APS signal out-of-range high

133 - APS/IVS APS signal in-range DTC

134 - APS/IVS APS signal and IVS disagree

135 - APS/IVS Idle Validation Switch circuit fault

136 - EFP Engine Fuel Pressure signal out-of-range low

137 - EFP Engine Fuel Pressure signal out-of-range high

141 - VSS Vehicle Speed Sensor signal out-of-range low

142 - VSS Vehicle Speed Sensor signal out-of-range high

143 - CMP Incorrect CMP signal signature

145 - CMP CMP signal inactive

146 - CKP CKP signal inactive

147 - CKP Incorrect CKP signal signature

151 - BAP Barometric Absolute Pressure signal out-of-range high

152 - BAP Barometric Absolute Pressure signal out-of-range low

153 - WIF Water In Fuel signal out-of-range low

154 - IAT Inlet Air temperature signal out-of-range low

155 - IAT Inlet Air temperature signal out-of-range high

161 - MAT Manifold Air Temperature Signal out-of-range low

162 - MAT Manifold Air Temperature Signal out-of-range high

163 - EGR Exhaust Gas Recirculation Valve Position Signal out-of-range low

211 - EOP Engine Oil Pressure signal out-of-range low

212 - EOP Engine Oil Pressure signal out-of-range high

215 - VSS Vehicle Speed Sensor signal frequency out-of-range high

225 - EOP EOP sensor signal in-range fault

231 - ATA ATA data communication link error

236 - ECL ECL switch circuit fault

241 - IPR Injection Control Pressure regulator OCC self test failed

246 - EFAN Engine Fan - OCC self test fault

247 - BSV Engine Brake enable OCC self test failed

251 - IAH Inlet Air Heater OCC self test failed

256 - RSE Radiator Shutter Enable OCC fault

261 - VGT Variable Geometry Turbo control OCC self test failed

267 - ECI Engine Crank Inhibit OCC self test failed

311 - EOT Engine Oil Temperature signal out-of-range low

312 - EOT Engine Oil Temperature signal out-of-range high

313 - EWPS Engine Oil Pressure below warning level

314 - EWPS Engine Oil Pressure below critical level

315 - EWPS Engine speed above warning level

316 - EWPS Engine Coolant Temp unable to reach commanded set point

321 - EWPS Engine Coolant Temperature above warning level

322 - EWPS Engine Coolant Temperature above critical level

323 - EWPS Engine Coolant Level below warning/critical level

324 - IST Idle Shutdown Timer enabled engine shutdown

325 - EWPS Power reduced, matched to cooling system performance

331 - ICP SYS Injection Control Pressure above system working range

332 - ICP SYS Injection Control Pressure above spec. with engine not running

333 - ICP SYS Injection Control Pressure above/below desired level

334 - ICP SYS ICP unable to achieve setpoint in time (poor performance)

335 - ICP SYS ICP unable to build pressure during cranking

341 - EBP Exhaust Back Pressure signal out-of-range low

342 - EBP Exhaust Back Pressure signal out-of-range high

343 - AMS Excessive exhaust back pressure (gauge)

344 - EBP Exhaust back pressure above spec. when engine off

345 - AMS Faults detected during VGT portion of the AMS Test

346 - AMS Faults detected during EGR portion of the AMS Test

351 - AMS Change in exhaust back pressure did not occur when expected

353 - AMS Variable Geometry Turbo control over duty cycle

354 - AMS Variable Geometry Turbo control under duty cycle

355 - AMS Variable Geometry Turbo overspeed

361 - AMS VGT control input (MAP/EBP) above/below desired level

365 - AMS EGR Valve Position above/below desired level

368 - AMS EGR driver module/ECM2 communication fault

371 - EFP Engine Fuel Pressure is above normal operating range

372 - EFP Engine Fuel Pressure is below normal operating range

421-426 - INJ High side to low side open (cylinder number indicated)

431-436 - INJ High side shorted to low side (cylinder number indicated)

451-456 - INJ High side short to ground or V BAT (cylinder number indicated)

523 - IDM IDM V IGN voltage low

525 - IDM IDM fault

533 - IDM IDM relay voltage high

534 - IDM IDM relay voltage low

546 - BCP Engine Brake Contol Pressure is below expected range

547 - BCP Engine Brake Contol Pressure is above expected range

543 - ECM/IDM ECM/IDM communications fault

551 - ECM/IDM IDM/CMPO signal inactive

552 - ECM/IDM IDM incorrect CMPO signal signature

553 - ECM/IDM IDM CKPO signal inactive

554 - IDM incorrect CKPO signal signature

613 - ECM ECM/IDM software not compatible

614 - ECM EFRC/ECM configuration mismatch

621 - ECM Engine using mfg. default rating

622 - ECM Engine using field default rating

623 - ECM Invalid Engine Family Rating Code (EFRC)

624 - ECM Field default active

626 - ECM PWR Unexpected reset fault

631 - ECM Read Only Memory (ROM) self test fault

632 - ECM Random Access Memory (RAM) - CPU self test fault

655 - ECM Programmable parameter list level incompatible

661 - ECM RAM programmable parameter list corrupt

664 - ECM Calibration level incompatible

665 - ECM Programmable parameter memory content corrupt

John_G
01-17-2009, 05:42 PM
One word of *CAUTION*...

Using DTCs for troubleshooting without good knowledge of the SYSYTEM that you are having issues with, you are setting yourself up for replacing lots of parts and fixing little.

quality towing
03-10-2009, 11:30 PM
looking for flash codes for 2005 inter dt466

quality towing
03-10-2009, 11:39 PM
thank you for your help

coryhoffa
06-01-2009, 07:21 PM
im so glad someone has come out with this info and i dont have to pay for it

domniman2002
08-24-2009, 03:26 PM
word of caution, chasing historic codes will send you into a nightmare condition. you should use a reader that can determine how old the codes are that you are chasing. what kind of problem are you having with this blue toy, some of us out here are pretty good with them and have probly seen what is wrong........what is it doing?

RLE6879
11-02-2009, 03:06 PM
i have a dt466e 98 model wont start unless u either it getting 626 code can u help

domniman2002
11-15-2009, 04:36 PM
sounds like a pwr issue with the voltage going to the ecm. need to check the ecm fuse to make sure that it is not blown. down in the battery box in most models, need to go to the main power wire at the ecm and see if you have power with the key on. also need to push in on the diagnostic button on the dash when you turn on the key and see if the ecm is flashing the lights on the left side of the dash cluster to see if the ecm is even talking. if you have power to the ecm and no lights on the dash that are flashing fault codes you need to take it to a certified shop so they can hook the scan tool or the laptop to it to diagnose exactly what is wrong....some things are better left to the techs that know what to do.......sorry.....if the ecm is dead....it will never start

kadena.RFM
01-11-2010, 01:14 AM
We got couple of 05 International truck that has VGT problem. Code 152 (BAP signal out of range low). 354 (VGT control under duty cycle) and Body Controller - Remote Engine Speed Control #1 - Analog input #2 shorted to ground. Already replace BAP sensor, MAP sensor and VGT turbo. Already check of short to ground on all wiring connected to BAP and MAP sensors. Any point of contact or Any help will be greatly appreciated. Thank you

MKEYES@KW LIVERPOOLNY
12-28-2010, 02:12 PM
to: 2003edge, i read all these questions and replies. i am looking for some help with a 2006 4300 w dt466e. using a prolink it states it has an active sid:146 fmi:7 can you possibly help me? thank you in advance

Boilerman
01-20-2012, 05:35 PM
Hi glad I found this place. Right now I working near the Northwest territory border, in Helmet British Columbia. My quit in the middle of the night. Had to leave it run due to the -42 weather. Nearest wrench puller is 9 hours away. My truck is giving me 3 different fault codes. Any help will be greatly app.

2006 International 7300

fault codes

1 - 1
613 - 14P

7 - 0
625 14P

150 - 9
2023 - 14P

Boilerman
01-22-2012, 02:57 AM
As it turns out these are ac codes. The problem was the EDM. Up and running again.