Join Date: Oct 2005
Posts: 284
Points: 3,208
Thanks: 0
Thanked 0 Times in 0 Posts
|
|
LinkBack | Thread Tools | Display Modes |
what would i need
Hey i have a 95 e350 motorhome with a 460 and auto trans in it, what all would be needed to convert it to a 7.3? would it have to be the 94-97 7.3 or could i use a 99up? what electronics need to be changed? fuel tank an lines obviously?? 460 dont cut i lol anyone done a 460 to 7.3 swap?
Joey aka pb
Joey aka pb
| Sponsored Links | |||
|
Advertisement
|
|
||
Join Date: Mar 2006
Posts: 1,132
Points: 20,038
Thanks: 7
Thanked 2 Times in 2 Posts
Threadstarter
Join Date: Oct 2005
Posts: 284
Points: 3,208
Thanks: 0
Thanked 0 Times in 0 Posts
he doesnt say how he did it? im just curious on pcms putting it in another ford might be easier than a chev??
Threadstarter
Join Date: Oct 2005
Posts: 284
Points: 3,208
Thanks: 0
Thanked 0 Times in 0 Posts
he doesnt say how he did it? im just curious on pcms putting it in another ford might be easier than a chev??
Join Date: Mar 2006
Posts: 1,132
Points: 20,038
Thanks: 7
Thanked 2 Times in 2 Posts
You would need all electronics to get a Powerstroke to work.IDM PCM.Fuel tank and lines would probably be fine just clean the Gas out 1st.You would also need a trans adaptor or a 4R100 trans to make it work.
I would PM him and ask.I know it would be a project that I would not want to tackle unless I had a full week to dig at it.
I would PM him and ask.I know it would be a project that I would not want to tackle unless I had a full week to dig at it.
Threadstarter
Join Date: Oct 2005
Posts: 284
Points: 3,208
Thanks: 0
Thanked 0 Times in 0 Posts
i can take months if i need to
lol
lol
Supporting Vendor
Join Date: Aug 2005
Posts: 484
Points: 26,699
Thanks: 0
Thanked 0 Times in 0 Posts
I think this would be easiest if you get a 94-97 motor. You would need the engine and trans as the bolt pattern is different between gas and diesel w/ the 7.3's ont the trans. Buy a vehicle side engine harness from a wrecked truck or stealership and you would be off to a good start. I would start looking at junk yards for wrecked E350's w/ the 7.3 and take as much as you can. Could be a fun project! Let me know if I can help. I have a semi torn down 97 at the house. I won't need the front cover and other misc parts.
Dave
Dave
D2 Hi-Performance
www.d2hiperformance.com
Proud to be a sponser of THE DIESEL GARAGE.COM!
(586) 709-2271
(586) 949-3234
Our rides
Dave P's Truck: 2002 CCSB 6.5" ProComp lift w/ 5100 Bilsteins, Crower Rods, Balanced rotating, coated rod and main bearings, ARP Head and Main studs, Fire Ringed, ported heads, machined and coated Mahle pistons, AFE stg II, Stealth pumps, BD's w/ 0.008 EH tips, D2HP Inconel exhaust valves, D2HP custom pushrods, Custom HX50 bolted to Hmax pedistal, Suncoast Comp trans, Detriot Electrac's front and rear, D2HP transfer case and 1 piece 4" Al driveshaft.
Dave D's Truck: 2002 ECLB Built Ford Tough Package 6" DR lift kit, Bilstein 5100's, 36x15.50R20 MTZ's on 20x10 114 Eagle's, Randy Ellis Bar w/4 8" Stainless ProComp 130W Lights, Custom tunes from DP Tuner, 05 Harley front end, D2HP transfer case and 1 piece Al driveshaft.
Becky P's ride: 2002 Limited Excursion, DVD, heated seats, TS and DP tunes, Edge Juice & Attitude, Dual exhaust, Bilstein stock replacments, AFE.
| Thread Tools | |
|
Show Printable Version Show Printable Version
Email this Page Email this Page
|
|
| Display Modes | |
|
|
| Posting Rules | |
