Hub price - Diesel Truck Forum - TheDieselGarage.com
Thread Details Posted by StrokinSnyd, this thread has received 29 replies and been viewed 2476 times.

Reply
 
LinkBack Thread Tools Display Modes
post #1 of 30 (permalink) Old 10-13-2007, 04:12 AM Thread Starter
TDG MAFIA #94
 
StrokinSnyd's Avatar
 
Join Date: Sep 2006
Posts: 519
Points: 2,546
Thanks: 5
Thanked 0 Times in 0 Posts
Send a message via MSN to StrokinSnyd
Thumbs down Hub price

ok, so the hubs are now officialy junk on the truck . grabed ahold of the 4x4 shaft going into the hub and could wiggle it about 3/8 of an inch (Not so good) so what is a good price and where can i get these:shrug: ...and help fixing this prob!:sofa

96 Dodge Cummins EC LB 5 spd big valve springs, full cut DV's, Big sticks, phat shaft turbo....yada yada yada.... plain and simple, it goes fast and pulls whatever
StrokinSnyd is offline  
Sponsored Links
Advertisement
 
post #2 of 30 (permalink) Old 10-13-2007, 04:23 AM
 
Join Date: Feb 2007
Posts: 204
Points: 2,463
Thanks: 0
Thanked 0 Times in 0 Posts
The cheapest I found was $230 from Advance Auto Parts. That's what I am running on my truck now, and I have put aprox. 15,000 miles on it so far.
imported_ryan is offline  
post #3 of 30 (permalink) Old 10-13-2007, 04:44 AM
Senior Member
 
midwestoffroad's Avatar
 
Join Date: Jan 2009
Posts: 463
Points: 18,384
Thanks: 5
Thanked 0 Times in 0 Posts
so what was bad the wheel bearing hub unit or the inner bearing

if you axle shaft has that much play it may be the inner bearing which is 7 bucks and you will probably need a new seal which depending if it is ABS or non abs is 30 or less.

if the inner bearing did go out since there is now way to grease it with out pulling the hub off you may also need a new stub shaft (127.00) when the bearing goes it will groove the stub shaft

new replacement hubs run 230-450
midwestoffroad is offline  
post #4 of 30 (permalink) Old 10-13-2007, 06:03 AM
Senior Member
 
Join Date: Dec 2008
Location: Sunbury, OH
Posts: 608
Points: 26,340
Thanks: 23
Thanked 24 Times in 12 Posts
just save your self the time and money... go with the dynatrac kit... I didn't and ended up just parts on both sides, the whole works stub shafts and all right at $1600...

early '99 converted to late '99 F-350 dually, 4x4, 4 door, long bed, 6 speed. Midwest transmissions 05+ zf-6 transmission with their short throw shifter and SB clutch. Rosewood 180cc with 80% nozzles, Termy modded 17* HPOP, International bellowed up pipes, fs-2500, DP Tunes. A few other things here and there...
dually club member.. Why replace 5 tires when you can replace seven? I like my training wheels...
calebgriffin31 is offline  
post #5 of 30 (permalink) Old 10-16-2007, 02:44 AM Thread Starter
TDG MAFIA #94
Threadstarter
 
StrokinSnyd's Avatar
 
Join Date: Sep 2006
Posts: 519
Points: 2,546
Thanks: 5
Thanked 0 Times in 0 Posts
Send a message via MSN to StrokinSnyd
yeah...um im not much of a mechanic, but im getting there...a little detail as to what these things are (location) would help bunches!!

96 Dodge Cummins EC LB 5 spd big valve springs, full cut DV's, Big sticks, phat shaft turbo....yada yada yada.... plain and simple, it goes fast and pulls whatever
StrokinSnyd is offline  
post #6 of 30 (permalink) Old 10-16-2007, 02:51 AM
Senior Member
 
Join Date: Dec 2008
Location: Sunbury, OH
Posts: 608
Points: 26,340
Thanks: 23
Thanked 24 Times in 12 Posts
go to dynatrac.com and take a look at their free spin kit. To my knowledge it is all bolt on. I knew nothing about the D60 axle until I tore into mine in the driveway with a friend and a book... they aren't that difficult. If you have any questions, keep them coming.

early '99 converted to late '99 F-350 dually, 4x4, 4 door, long bed, 6 speed. Midwest transmissions 05+ zf-6 transmission with their short throw shifter and SB clutch. Rosewood 180cc with 80% nozzles, Termy modded 17* HPOP, International bellowed up pipes, fs-2500, DP Tunes. A few other things here and there...
dually club member.. Why replace 5 tires when you can replace seven? I like my training wheels...
calebgriffin31 is offline  
post #7 of 30 (permalink) Old 10-16-2007, 04:33 PM Thread Starter
TDG MAFIA #94
Threadstarter
 
StrokinSnyd's Avatar
 
Join Date: Sep 2006
Posts: 519
Points: 2,546
Thanks: 5
Thanked 0 Times in 0 Posts
Send a message via MSN to StrokinSnyd
haha alright...how long can i drive like this? i have to get to school and work daily and this is my only mode of transportation so ill try and get it done this weekend if i can go that long, or sooner if need be?

ha, man now i feel really stupid. just went to the web site and got lost about what they are talkin about asap. what is the free spin kit? what dose it do/replace/fix?

96 Dodge Cummins EC LB 5 spd big valve springs, full cut DV's, Big sticks, phat shaft turbo....yada yada yada.... plain and simple, it goes fast and pulls whatever
StrokinSnyd is offline  
post #8 of 30 (permalink) Old 10-17-2007, 03:57 AM
Senior Member
 
Join Date: Dec 2008
Location: Sunbury, OH
Posts: 608
Points: 26,340
Thanks: 23
Thanked 24 Times in 12 Posts
I drove with a little vibration in 4 hi with the front hubs unlocked for almost 1000 miles... and try this site http://www.dynatrac.com/products_freespin_ford.html

early '99 converted to late '99 F-350 dually, 4x4, 4 door, long bed, 6 speed. Midwest transmissions 05+ zf-6 transmission with their short throw shifter and SB clutch. Rosewood 180cc with 80% nozzles, Termy modded 17* HPOP, International bellowed up pipes, fs-2500, DP Tunes. A few other things here and there...
dually club member.. Why replace 5 tires when you can replace seven? I like my training wheels...
calebgriffin31 is offline  
post #9 of 30 (permalink) Old 10-17-2007, 06:50 AM
Senior Member
 
midwestoffroad's Avatar
 
Join Date: Jan 2009
Posts: 463
Points: 18,384
Thanks: 5
Thanked 0 Times in 0 Posts
dynatrack kit has had a few price increases closer to 1900 now
midwestoffroad is offline  
post #10 of 30 (permalink) Old 10-17-2007, 04:06 PM Thread Starter
TDG MAFIA #94
Threadstarter
 
StrokinSnyd's Avatar
 
Join Date: Sep 2006
Posts: 519
Points: 2,546
Thanks: 5
Thanked 0 Times in 0 Posts
Send a message via MSN to StrokinSnyd
haha well i guess i duno wtf to do about fixing it...the free spin kit would be the best way to go, but thats about 2,000 that i aint got to spend at the moment...but the hubs are cheaper...so any advice on what to do is apriciated!

96 Dodge Cummins EC LB 5 spd big valve springs, full cut DV's, Big sticks, phat shaft turbo....yada yada yada.... plain and simple, it goes fast and pulls whatever
StrokinSnyd is offline  
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Diesel Truck Forum - TheDieselGarage.com forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome